RAD Data comm ASMi-52L Especificaciones descargar pdf (Pagina 24)

Quick Start Guide Installation and Operation Manual

4 Configuring ASMi-52 ASMi-52 Ver. 2.8

Configuring the 10/100BaseT Interface

³ To configure 10/100BaseT parameters:

• From the LAN Configuration menu (Main Menu > Configuration > System

Configuration > LAN Configuration), configure the following LAN parameters:

 Bridge static table

 Aging timeout

 LAN rate

1 2 ... 19 20 21 22 23 24 25 26 27 28 29 ... 183 184

2/4-Wire SHDSL Modem 1
Limited Warranty 4
Product Disposal 4
General Safety Instructions 5
Safety Symbols 5
Handling Energized Products 6
Caution 8
Attention 8
FCC-15 User Information 9
Mise au rebut du produit 10
Symboles de sécurité 10
Français 11
Declaration of Conformity 13
Glossary 15
Quick Start Guide 21
Configuring the Master Clock 22
Configuring the T1 Interface 23
Contents 25
ASMi-52 Ver. 2.8 iii 27
Chapter 1 29
Introduction 29
ASMi-52 Ver. 2.8 30
DTE Interface 33
DTE+LAN 36
Dial-In 37
Dial-Out 37
1.3 Functional Description 39
ASMi-52 Ver. 2.8 40
Chapter 2 45
Installation and Setup 45
Connecting to DTE Equipment 49
³ To connect DC power: 51
Chapter 3 53
Operation 53
Rear Panel Indicators 55
3.3 Default Settings 56
Working with Terminal 60
Choosing Options 61
Working with Web Terminal 62
Working with ConfiguRAD 63
Working with RADview 64
Working with SNMP 64
Menu Map 65
3.5 Turning Off ASMi-52 68
Chapter 4 69
Configuration 69
Entering Device Information 70
Selecting the CTS State 76
Selecting the DSR State 76
Timeout 78
Appendix A 79
Local Card Mode 83
Remote Card Mode 83
Configuring the Snext Margin 86
Configuring Line Probing 88
Configuring the E1 Interface 90
Selecting E1 Framing Mode 92
Setting the Sync Mode 93
Defining Idle Code 94
Mapping E1 Timeslots 94
Configuring the LAN Port 99
Configuring Aging Timeout 101
Configuring QoS Mapping 101
Setting the LAN Rate 102
Configuring Autonegotiation 104
Detecting SHDSL Link Failure 104
Displaying the System Status 105
Displaying the Port Status 106
Accessing the Remote ASMi-52 107
4-41. Inventory Screen 108
ASMi-52 110
Main menu 110
ConfiguRAD 110
4-46. TFTP Menu 111
Switching Software Versions 114
Resetting ASMi-52 115
Resetting the ASMi-52 Modem 116
Resetting the SHDSL Repeater 117
4-52. Repeater Reset Menu 118
Chapter 5 119
Monitoring and 119
Diagnostics 119
Displaying E1/T1 Statistics 122
5.2 Detecting Errors 126
5.3 Handling Events 126
Displaying All Alarms 127
Masking Port Alarms 129
5-4. ASMi-52 Events 132
5-15. Port Log File Screen 133
Handling Traps 134
5.4 Troubleshooting 135
Running Loopback Tests 138
Running the Local Loopback 139
Running the Remote Loopback 141
Deactivating the Loopbacks 142
Running the LEDs Test 143
5.7 Technical Support 146
Chapter 6 147
Software Upgrade 147
6.4 Prerequisites 148
Utilities Menu 148
Activating the TFTP Server 150
6-4. TFTP Menu 151
Using the XMODEM Protocol 153
6-6. Boot Manager Menu 154
Using the TFTP 155
Chapter 7 157
Application Tutorial 157
Installing LRS-16 158
Copper Cable 160
Station Clock Port 160
Configuring the Host IP 161
7-8. Host Screen 162
Setting Management Access 163
Configuring the E1 Port 165
7-16. Station Clock Screen 167
Chapter 4 167
Running Diagnostic Tests 168
7-19. Local Tests Screen 169
Displaying Alarms 170
Event Reporting 172
Appendix A 173
Connection Data 173
A.2 SHDSL Interface 175
A.3 CONTROL Connector 176
A.4 Alarm Relay Connector 177
A-2. ALARM Pin Functions 178
Customer Response Form 179
Error Report 181
The Access Company 184

Comentarios a estos manuales

Sin comentarios

RAD Data comm ASMi-52L Especificaciones Pagina 24

Comentarios a estos manuales

Relacionado con productos y manuales para Redes RAD Data comm ASMi-52L