RAD Data comm FCD-G703 Manual de usuario

Busca en linea o descarga Manual de usuario para Redes RAD Data comm FCD-G703. FCD-E1A - comtec Manual de usuario

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 6
  • Tabla de contenidos
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 0
FCD-E1A
E1 or Fractional E1 Access Unit
FEATURES
Managed access for E1 and
fractional E1 services
One or two data ports with
selectable sync data rates:
n × 56, n × 64 kbps
Optional sub-E1
drop-and-insert user port for
PBX connectivity
Failure-immune sub-E1 port
ensuring uninterrupted
service (G.703 only)
Data port interfaces: V.35,
RS-530, V.36/RS-449, or
X.21
Optional Ethernet or Fast
Ethernet bridge, with or
without VLAN support or IP
router
Four ISDN BRI "S" interface
user ports
Management:
Out-of-band via V.24
supervisory port or
Ethernet management
port
Inband via TS0 or
dedicated timeslot
Dial-in option for remote
out-of-band management
Dial-out for alarm report
SNMP agent
Optional integrated ISDN
backup
E1 interface complies with:
ITU G.703, G.704, G.706,
G.732, and G.823
Enhanced diagnostics
include:
User-activated local and
remote loopbacks
Integrated BER tester
Fractional E1 inband loop
DESCRIPTION
FCD-E1A is an access unit for E1
or fractional E1 services. It can be
used as a rate and interface
converter, or as an integrating
multiplexer for E1 and fractional
E1 services (see Figures 1 and 2).
FCD-E1A operates opposite RAD's
modular DXC multiservice access
nodes or other vendors’ E1
equipment, for multilink star
applications such as SDH network
access. DXC and FCD-E1A units
operate together under centralized
SNMP network management (see
Figure 3).
FCD-E1A can be ordered with
either a standard electric (G.703)
or a fiber optic E1 main link.
These options are also available
with an optional sub-E1
drop-and-insert port. The unit can
be ordered with either one or two
data ports. Alternatively, an
Ethernet bridge/router port is
available instead of a second data
port.
BASIC UNIT
The basic unit includes a power
supply, one E1 main link, and one
data port.
The electrical E1 interface is
compatible with virtually all
carrier-provided E1 services and
meets ITU recommendations
G.703, G.704, G.706, and G.732.
It supports both 2 and 16 frames
per multiframe, with or without
CRC-4. Line coding is HDB3. The
integral LTU (soft-configurable)
ensures a range of up to 2 km
(1.2 miles).
FCD-E1A can be ordered with a
fiber optic link to eliminate the
need for an external fiber optic
modem. The fiber optic link
provides a secure link in hazardous
or hostile environments. It
complies with ITU standards
G.921 and G.956.
The following fiber optic interfaces
are available:
850 nm laser transmitter for
multimode fiber of up to 5 km
(3 miles)
1310 nm laser transmitter for
single mode fiber of up to 62 km
(38 miles)
1550 nm laser transmitter for
single mode fiber for extended
range of up to 100 km
(62 miles).
Vista de pagina 0
1 2 3 4 5 6

Indice de contenidos

Pagina 1 - FCD-E1A

FCD-E1A E1 or Fractional E1 Access Unit FEATURES • Managed access for E1 and fractional E1 services • One or two data ports with selectable syn

Pagina 2

E1 or Fractional E1 Access Unit FCD-E1A Figure 1. Extended Ethernet Management over E1 Network • Timeslot assignment is programmable, allowing da

Pagina 3

• The IR-ETH/QN port is available with a 10/100BaseT interface. The other Ethernet port options are available only with a 10BaseT (UTP) interface

Pagina 4 - SPECIFICATIONS

E1 or Fractional E1 Access UnitFCD-E1A Figure 3. SDH Access Solution for Multiple Remote Sites SPECIFICATIONS ELECTRIC E1 MAIN LINK (NETWORK) AN

Pagina 5

FCD-E1AE1 or Fractional E1 Access Unit Table 1. Fiber Optic Interface Characteristics Operating Wavelength [nm] Fiber Type [µm] Typical Output Pow

Pagina 6

 1991–2006 RAD Data Communications Ltd. Specifications are subject to change without prior notice. All other trademarks are the property of their res

Comentarios a estos manuales

Sin comentarios