RAD Data comm FCD-G703 Manual de usuario descargar pdf (Pagina 6)

 1991–2006 RAD Data Communications Ltd. Specifications are subject to change without prior notice.

All other trademarks are the property of their respective holders.

FCD-E1A

E1 or Fractional E1 Access Uni

201-100-01/06

www.rad.com

International Headquarters

24 Raoul Wallenberg Street

Tel Aviv 69719, Israel

Tel: 972-3-6458181

Fax: 972-3-6498250

Email: [email protected]

North America Headquarters

900 Corporate Drive

Mahwah, NJ 07430, USA

Tel: (201) 529-1100

Toll free: 1-800 444-7234

Fax: (201) 529-5777

Email: [email protected]

• Physical

Height: 4.3 cm (1.7 in) (1U)

Width: 21.5 cm (8.5 in)

Depth: 24.3 cm (9.5 in)

Weight: 1.3 kg (2.9 lb)

• Power

AC: 100 to 240 VAC; 47 to 63 Hz

DC: -48 VDC (40 to 57 VDC)

• Power consumption

10W max

• Environment

Temperature: 0°–50°C (32°–122°F)

Humidity: up to 90%,

non-condensing

ORDERING

FCD-E1A/*/~/$/&/%/#+

E1 or fractional E1 access unit

* Specify S1 for optional

drop & insert sub-E1 port.

(Default is without sub-E1 port)

~ Specify power supply type:

AC for 110 VAC to 240 VAC

48 for -48 VDC

$ Specify management port

interface:

V24 for V.24/RS232 (DB-9)

UTP for Ethernet 10BaseT (UTP)

& Specify data port interface:

530 for RS-530 interface

V35 for V.35 interface

X21 for X.21 interface

449 for V.36/RS-449 interface

% Specify optional second data port

interface:

530 for RS-530 interface

V24 for V.24 interface

V35 for V.35 interface

X21 for X.21 interface

449 for V.36/RS-449 interface

ETUB for IR-ETH UTP Ethernet

bridge (10BaseT)

ETUQ for IR-ETH/Q UTP Ethernet

bridge VLAN (10BaseT)

ETQN for IR-ETH/QN UTP

Ethernet bridge VLAN

(10/100BaseT)

ETUR for IR-IP UTP Ethernet router

(10BaseT)

S0 for 4×S0 ISDN

IBE for ISDN backup “S” interface

# Specify link connector type:

ST for ST type fiber connectors

FC for FC/PC type fiber connectors

SC for SC type fiber connectors

(Default is G.703 electrical/copper

interface)

+ Specify optical interface wavelength

and transmitter type (not relevant for

copper interface):

85 for 850 nm, multimode, laser

13L for 1310 nm, single mode, laser

15L for 1550 nm, single mode, laser

SUPPLIED ACCESSORIES

AC power cord (when AC power

supply is ordered)

DC adapter plug (when DC power

supply is ordered)

The following cables (suitable for use in

DCE clock mode only) are supplied for

each data port interface specified. Cable

length is 2m (6 ft):

CBL-HS2/V/1 for 34-pin V.35, DCE

CBL-HS2/R/1 for 37-pin V.36, DCE

CBL-HS2/X/1 for 15-pin X.21, DCE

OPTIONAL ACCESSORIES

RM-17

Hardware kit for mounting one or two

units side-by-side in a 19-inch rack

CBL-HS2/*/#

Adapter cables for DB-25 channel

connectors

* Specify interface, clock mode:

V/2 for 34-pin V.35, DTE1

V/3 for 34-pin V.35, DTE2

R/2 for 37-pin V.36/RS-449, DTE1

R/3 for 37-pin V.36/RS-449, DTE2

# Specify cable connector type:

F for female

M for male

Table 2. Ethernet Interface Modules Characteristics

Interface

Module

LAN Table

[addresses]

Filtering and

Forwarding

[frames/second]

Buffer

[frames]

Line Code WAN Protocol

IR-ETH 10,000 15,000 256 Manchester HDLC

IR-ETH/Q 2,000 2,000 256 Manchester HDLC

IR-ETH/QN 1,000 150,000 85  10BaseT: Manchester

 100BaseT: MLT3

HDLC

IR-IP IP Addresses

256

Filtering 35,000

Forwarding 30,000

256 Manchester  PPP (PAP/CHAP)

 Frame Relay (RFC 1490)

 HDLC

Note: All the Ethernet interface modules conform to the IEEE 802.3/Ethernet V2 standard. Additionally, IR-ETH/Q

supports IEEE 802.1/q frames, and IR-ETH/QN conforms to IEEE 802.1Q (relevant parts), 802.1p and 802.3x.

1 2 3 4 5 6

FCD-E1A 1
SPECIFICATIONS 4

Comentarios a estos manuales

Sin comentarios

RAD Data comm FCD-G703 Manual de usuario Pagina 6

Comentarios a estos manuales

Relacionado con productos y manuales para Redes RAD Data comm FCD-G703