
137
5
RAD Data Communications 2011 Catalog
•
Extends the range of E3 or T3 signals
over fiber optic cable up to 110 km
(68 miles)
•
Wave Division Multiplexing (WDM)
module for operation over a single fiber
strand
•
Wide range of optical modules including
long haul lasers for extended range
•
Operates opposite Optimux, ACE and
DXC
•
Built-in diagnostics comply with V.54
standard
•
Dry contact alarm port for external
alert devices
The high speed FOM-E3 and FOM-T3 fiber optic
modems extend transmission range of electrical
E3 or T3 signals over fiber optic cables up to
110 km (68 miles).
Two models are available:
•
FOM-E3 for E3 rates (34.368 Mbps)
•
FOM-T3 for T3 rates (44.736 Mbps)
The FOM-E3 and FOM-T3 support a wide range
of fiber optic interfaces, including long haul
laser for extended ranges and WDM laser for
transmission over a single fiber.
Transparent to E3/T3 framing, the FOM-E3 and
FOM-T3 modems operate opposite RAD’s DXC
cross connect, Optimux-134 multiplexer (FOM-E3)
and Optimux-45 multiplexer (FOM-T3). Similarly,
they can operate opposite an ACE ATM access
device, enabling E3/T3 ATM traffic to be
transported over long distances on fiber and
connect to an ATM or SDH network device with
an electrical E3/T3 port.
FOM-E3 and FOM-T3 operation complies with
ITU G.703, G.921 and G.956 standards. In
addition, the modems support activation of
local and remote loopbacks in compliance with
the ITU V.54 standard.
The FOM-E3 and FOM-T3 modems include a dry
contact alarm port for relay of alarm conditions
to external alert equipment.
FOM-E3, FOM-T3
E3, T3 Fiber Optic Modems
For latest updates visit www.rad.com
FIBER MODEMS
•
Extends the range of equipment with
electrical E3, T3 or HSSI interfaces
•
Inband management on both local and
remote units
•
Redundancy on fiber optic link and
power supply
•
Wave Division Multiplexing (WDM)
module for operation over a single-
strand fiber optic link
•
Works opposite Optimux, ACE and DXC
•
Different clock modes including central
system clock
•
Wide range of modular optical
interfaces
The FOMi-E3 and FOMi-T3 are high speed fiber
optic modems that extend the transmission range
of electrical E3 or T3 over fiber optic cables:
FOMi-E3 for E3 rates (34.368 Mbps)
FOMi-T3 for T3 rates (44.736 Mbps)
Both modems can optionally support an HSSI
DCE interface, which operates at the same rate
as the modem type into which it is inserted (E3
at 34.368 Mbps and T3 at 44.736 Mbps). The
HSSI option also supports bit rates of one-half
and one-fourth of the main link rate. This option
enables connection of high speed HSSI routers
over backbones at E3 or T3 rates.
The FOMi-E3 and FOMi-T3 can substitute for an
ACE, DXC or Optimux unit at the central office
that works opposite identical devices at the
customer premises, thereby enabling low-cost
extension and conversion of E3/T3 fiber
interfaces to standard electrical interfaces. When
replacing an Optimux device at the central
office, the FOMi-E3 or FOMi-T3 enables the use
of one E3/T3 port on the ADM rather than using
many E1/T1 ports.
The optical interface of the FOMi-E3 or FOMi-T3
is modular. The modems support the wide range
of optical modules supported by the Optimux.
These modules include multimode, single mode,
laser, long haul laser, WDM, and all types of
optical connectors. There is an option to install
two optical interfaces for full redundancy of the
optical link. There is also an option of dual
power supplies for additional redundancy.
FOMi-E3 and FOMi-T3 feature flexible
management capabilities, including local
management via an ASCII terminal (RS-232). In
addition, remote management can be performed
out-of-band using a dedicated management
protocol.
FOMi-E3, FOMi-T3
E3, T3 and HSSI Manageable Fiber Optic Modems
For latest updates visit www.rad.com
Comentarios a estos manuales