RAD Data comm ASM-20 Especificaciones Pagina 30
- Pagina / 116
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 2 Installation and Setup Installation and Operation Manual
2-4 Installation and Setup ASM-40 Ver. 1.0
Table 2-1. ASM-40 Internal Jumpers and Switches
DIP Switch Function Possible Settings Factory
Setting
EX/R and INT
sections,
SW4/1, 2
Select the transmit clock INT – ON, internal clock.
EX/R section is disabled
EX/R – ON, INT – OFF, receive clock
EX/R – OFF, INT – OFF, external clock
INT – ON
EX/R – OFF
Note: When set to external clock, ASM-40 automatically configures itself to the DTE data rate, disabling SW3 (baud
rate).
B8ZS and AMI
sections,
SW4/3, 4
Select the line code B8ZS – OFF, AMI – ON, AMI line code
B8ZS – OFF, AMI – OFF, HDB3 or B8ZS line code,
depending on the selected data rate
B8ZS – OFF
AMI – OFF
Note: When setting data rate to 32, 64, 128, 256, 512, 1024, 1920 or 2048 kbps, the HDB3 line coding is
automatically selected. In this case the B8ZS and AMI section settings are irrelevant.
The B8ZS and AMI sections are in use only if the data rate is set to 192( B8ZS only), 384, 768, 1536 or 1544
kbps.
SWEN section,
SW3/1
Enables activation of the
loopbacks and internal BERT via
the front panel pushbuttons
ON – The diagnostic tests can be activated via
the front panel
OFF – The diagnostic tests cannot be activated
via the front panel
ON
V54E section,
SW3/2
Controls activation of the local
digital loopback when remote
digital loopback is initiated
from the remote unit
ON – Local digital loopback activation is enabled
OFF – Local digital loopback activation is
disabled
ON
CNTE section,
SW3/3
Selects the transmit carrier
mode
ON – Carrier follows the RTS line
OFF – Carrier is constantly ON
OFF
Note: For ASM-40 units with G.703 Codirectional DTE interface, the CNTE section (SW3/3) must be set to OFF.
B/UB section,
SW3/4
Selects the line impedance:
• Balanced: terminal block or
DB-15
• Unbalanced: BNC
ON – 75Ω (for 32, 64, 128, 256, 512, 1024,
1920 and 2048 kbps)
OFF – 120Ω (for 32, 64, 128, 256, 512, 1024,
1920 and 2048 kbps)
According to
the connector
type
Note: 100Ω line impedance is set by selecting one of the following data rates: 192, 384, 768, 1536 and 1544 kbps. In
this case, the settings of the SW3 B/UB section are ignored.
ALBE section,
SW3/5
Enables local analog loopback
activation from the DTE
(via pin 18 for V.24, RS-530,
V.36 or via pin “JJ” for V.35)
ON – The local analog loopback activation from
the DTE is enabled
OFF – The local analog loopback activation from
the DTE is disabled
OFF
Note
:
Set this section to DIS if the DTE interface does not support the local analog loopback activation via the
appropriate pin.
- High-Speed Short-Range Modem 1
- Limited Warranty 4
- Product Disposal 4
- General Safety Instructions 5
- Safety Symbols 5
- Handling Energized Products 6
- Attention 8
- FCC-15 User Information 9
- Declaration of Conformity 10
- Quick Start Guide 11
- 2. Operating ASM-40 13
- • DCD: On 14
- • TEST: Off 14
- Contents 15
- Chapter 1 17
- Introduction 17
- Features 18
- 1.2 Physical Description 19
- 1.3 Functional Description 19
- Timing Generator 20
- G.703-HDB3 Interface Timing 21
- Encoder/Decoder 22
- Line Driver 22
- 1.4 Technical Specifications 23
- Chapter 2 27
- Installation and Setup 27
- 2.2 Package Contents 28
- 2.3 Installation and Setup 28
- MT RCV GND 31
- Connecting the Line 32
- Connecting the DTE 32
- Connecting the Power 33
- Chapter 3 35
- Operation 35
- 3.2 Operating Procedure 36
- Normal Indications 37
- Turning ASM-40 Off 37
- Chapter 4 39
- Troubleshooting and 39
- Diagnostics 39
- Local Analog Loopback (LLB) 40
- Local Digital Loopback (DIG) 41
- Local ASM-40 Remote ASM-40 42
- 4.2 Internal BERT 42
- Two-BERT Test 43
- ASM-40 ASM-40 44
- Chapter 5 45
- ASM-40/R Card 45
- AC Supply 46
- 5.3 ASM-40/R Front Panel 47
- Figure 2-1 49
- Table 2-1 49
- Figure 5-4 49
- Connecting the Interfaces 51
- Appendix A 53
- Pinouts 53
- Table A-2 56
- Connection 57
- Chassis Ground 58
- RCV1* (input) 58
- RCV2 (input) 58
- XMT1 (output) 58
- XMT2* (output) 58
- Table A-6 59
- Appendix B 61
- IR-ETH Interface Module 61
- XMT RCV GND 62
- General 62
- Opening the ASM-40 Case 63
- Setting the DIP Switch 64
- Closing the ASM-40 Case 64
- LED Indicators 64
- Connecting the LAN 65
- Appendix C 67
- IR-ETH/QN (IR-ETH/Q) 67
- Interface Module 67
- ACT LINK 68
- IR-ETH/QN 68
- Setting the DIP Switches 70
- Appendix D 73
- IR-IP Interface Module 73
- D.2 Technical Specifications 74
- D.3 Physical Description 74
- IR-IP LEDs 75
- Connecting the Telnet Host 79
- What to Do If 81
- General Operating Procedures 82
- Figure D-5. IR-IP Main Menu 83
- Figure D-6 83
- D.7 Quick Setup Menu 84
- WAN IP Address 85
- WAN IP Mask 85
- Default Gateway 85
- D.8 Management Access Menu 86
- D.9 Advanced Setup Menu 87
- Device Identification Menu 88
- Interface Parameters Menu 88
- LAN Status 89
- WAN Status 89
- WAN Throttle 89
- Quick Setup Menu 90
- Figure D-7 90
- Figure D-13 90
- Protocol Field Compression 91
- Authentication Protocol 91
- Security Host/Guest 91
- User Name To Send 92
- Password To Send 92
- User Name To Accept 92
- Password To Accept 92
- Multicast IP Menu 93
- D.10 Device Control Menu 94
- New Software Download Menu 95
- View Error Log Screen 96
- Resets Menu 96
- Reset Device 97
- Reset LAN 97
- Reset WAN 97
- D.11 View Menu 98
- ARP Tables 99
- Statistics Screen 100
- Figure D-26 101
- Using the Ping Function 102
- D.14 Erasing IR-IP Software 104
- Performing 105
- Preliminary Configuration 105
- IR-G.703 Interface Module 107
- Appendix E 107
- EXT Timing 108
- INT/RCV Timing 109
- Customer Response Form 111
- Error Report 113
- Innovative Access Solutions 116
Relacionado con productos y manuales para Redes RAD Data comm ASM-20
Redes RAD Data comm T1 Especificaciones
(34 paginas)
(34 paginas)
Redes RAD Data comm Optimux-34 Información técnica
(82 paginas)
(82 paginas)
Redes RAD Data comm FOM-E3 Manual de usuario
(2 paginas)
(2 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.162 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales