RAD Data comm ASMi-52 Manual de usuario Pagina 134
- Pagina / 186
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Appendix A Interface Connector Specifications Installation and Operation Manual
A-4 CONTROL Connector ASMi-52 Ver. 2.5
A.2 CONTROL Connector
The control terminal interface terminates in a V.24/RS-232 9-pin D-type female
connector that can be configured as DCE or DTE (see the Selecting the Control
Port Interface section in Chapter 4). Table A-4 lists the CONTROL connector pin
assignments. Table A-5 describes the control signal direction.
Table A-4. CONTROL Connector Pinout
Pin Function
1 Data Carrier Detect (DCD)
2 Receive Data (RD)
3 Transmit Data (TD)
4 Data Terminal Ready (DTR)
5 Ground (GND)
6 Data Set Ready (DSR)
7 Request To Send (RTS)
8 Clear To Send (CTS)
9 Ring Indicator (RI)
Table A-5. CONTROL Connector Signal Direction
Interface Type
Control Signal
DCE DTE
CTS Out Not Used
DCD Out Out
DSR Out Out
DTR In In
RI Not Used In
RTS In In
When connected and turned on, the terminal sets the DTR line ON (active) to gain
control over ASMi-52 and starts a configuration or monitoring session.
When connecting a dial-out modem to the CONTROL port for the alarm
reporting, a cross cable must be used. Table A-6 provides the pinout of a typical
cross cable with two male DB-9 connectors.
Note
- /4-Wire SHDSL Modem 1
- ASMi-52 3
- Limited Warranty 4
- General Safety Instructions 5
- Handling Energized Products 6
- FCC-15 User Information 8
- Warning 9
- Declaration of Conformity 10
- Quick Start Guide 11
- Configuring the E1 Interface 12
- Configuring the T1 Interface 13
- Contents 15
- Table of Contents 16
- DTE Interface 17
- Line Interface 17
- Unit Enclosure 18
- Functionality 20
- Multiplexer Applications 23
- Management 25
- Statistics Collection 26
- Alarm Reporting 26
- SHDSL Repeaters 26
- 1.4 Technical Specifications 28
- Environment 31
- Chapter 2 33
- Installation and Setup 33
- 2.3 Package Contents 34
- Connecting the Line 35
- Connecting the DTE Interface 35
- Chapter 3 37
- Operation 37
- Preparing the Terminal 43
- Data Terminal Ready (DTR) 43
- Initiating a Control Session 43
- Correcting Entries 44
- Navigating Data Forms 44
- Configuration Menus 47
- Chapter 4 51
- Configuration 51
- Entering Device Information 52
- Configuring the LAN Port 57
- Configuring Aging Timeout 59
- Configuring QoS Mapping 59
- Setting the LAN Rate 60
- Configuring Autonegotiation 61
- Configuring Fault Indication 62
- Configuring Remote Card Mode 65
- Selecting the CTS State 67
- Selecting the DSR State 67
- Timeout 68
- Configuring the Snext Margin 73
- Configuring Line Probing 75
- Selecting E1 Framing Mode 79
- Setting the Sync Mode 80
- Defining Idle Code 81
- Mapping E1 Timeslots 81
- Displaying the System Status 86
- Displaying the Port Status 87
- Accessing the Remote ASMi-52 88
- Updating Software Releases 91
- Resetting ASMi-52 95
- Resetting the ASMi-52 Modem 96
- Resetting the SHDSL Repeater 97
- Chapter 5 99
- Configuring a Typical 99
- Application 99
- ASMi-52 Ver. 2.5 100
- Setting the E1 Port 101
- Chapter 6 105
- Troubleshooting and 105
- Diagnostics 105
- Displaying All Alarms 113
- Masking Port Alarms 115
- 6.4 Troubleshooting 119
- BERT Patterns 121
- Running Loopback Tests 123
- Running the Local Loopback 124
- Running the Remote Loopback 126
- Deactivating the Loopbacks 127
- 6.7 Technical Support 129
- Appendix A 131
- Interface Connector 131
- Specifications 131
- Ethernet Connector 133
- A.2 CONTROL Connector 134
- A.3 Alarm Relay Connector 135
- Appendix B 137
- IR-IP Interface Module 137
- B.2 Technical Specifications 138
- B.3 Physical Description 139
- IR-IP LEDs 140
- Normal Indications 140
- IP Learning Mechanism 143
- General Operating Procedures 145
- ASMi-52 with IR-IP 147
- LAN IP Address: 192.168.1.2 149
- Mask: 255.255.255.248 149
- DHCP Server 149
- IP Network 149
- Defining a Telnet Password 150
- B.9 Advanced Setup 151
- Frame Relay Protocol 153
- PPP Protocol Menu 154
- Downloading New Software 157
- Viewing the Error Log 157
- Reset LAN 158
- Reset WAN 159
- Viewing the ARP Tables 160
- Using the Ping Function 163
- B.14 Erasing IR-IP Software 164
- Erasing Application Software 165
- B.15 IR-IP Troubleshooting 166
- Appendix C 167
- Easy Config Device 167
- C.3 Installation 168
- C.4 Operation 169
- Assigning Timeslots 172
- ASMi-52 Ver. 2.5 I-5 177
- E1, 4-32 177
- Supplement 179
- Customer Response Form 181
- Error Report 183
Relacionado con productos y manuales para Gateways / Controladores RAD Data comm ASMi-52
(12 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.077 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales