RAD Data comm IPmux-8 Especificaciones Pagina 148
- Pagina / 174
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 6 Troubleshooting and Diagnostics Installation and Operation Manual
6-28 Testing the Units IPmux-8/16 Ver. 6.00
To activate an inband loopback:
• From the Loopback Configuration, perform the following:
1. Select Loopback State and set it to Disable.
2. Select Loopback Location and set it as follows:
Local System (External loopback is activated in the local IPmux-8/16)
Remote System (Internal loopback is activated in the remote
IPmux-8/16)
Transparent (Loopback activation code is transmitted to the remote
TDM device, which closes the loopback)
Disable (IPmux-8/16 ignores inband activation code).
3. Define Activate Loop Pattern (8-bit code to be sent by the adjacent TDM
device in order to activate a loopback)
4. Define Deactivate Loop Pattern (8-bit code to be sent by the adjacent
TDM device in order to deactivate a loopback).
T1 LOOPBACK CONFIGURATION
1. Loopback State Disable
2. Loopback Location Local System
3. Activate Loop Pattern 10000
4. Deactivate Loop Pattern 100
Select item from the menu.
Figure 6-12. T1 Loopback Configuration Menu
Running Ping Test
You can ping remote IP host to check the IPmux-8/16 IP connectivity.
To ping an IP host:
1. From the Main menu, select System.
The System menu is displayed.
2. From the System menu, select Ping.
The Ping menu is displayed (see
Figure 6-13).
3. From the Ping menu, enter IP address of the host that you intend to ping.
4. Press <Spacebar> to define the number of pings (1, 2, 3, 4 or Endless
Repeats).
5. Press <Enter> to start pinging.
- TDM Pseudowire Access 1
- Gateways 1
- IPmux-8, IPmux-16 3
- Limited Warranty 4
- General Safety Instructions 5
- Product Disposal 5
- Handling Energized Products 6
- FCC-15 User Information 9
- Declaration of Conformity 10
- Conventions 12
- Quick Start Guide 13
- Contents 15
- IPmux-8/16 Ver. 6.00 iii 17
- Chapter 1 19
- Introduction 19
- Applications 20
- Features 21
- 4-Port Ethernet Module 23
- 1-Port Ethernet Module 24
- Default Next Hop per Host 24
- Download (DL) Transparent 25
- Operation Modes for E1/T1 25
- Multibundling 25
- 1.2 Physical Description 27
- 1.3 Functional Description 28
- Unframed 29
- External Network Timing 30
- Single Source Clock Network 31
- Bundle Redundancy 32
- Frame Format 32
- MAC IP UDP CW 33
- VLAN Support 34
- Packet Delay Variation 35
- PDVT (Jitter) Buffer 36
- Packetization Delay 36
- Round Trip Delay 37
- Ethernet 37
- Ethernet Redundancy 38
- Load Sharing 38
- Rate Limiter Option 39
- Table 1-5. Mode A 40
- Table 1-6. Mode B 40
- Table 1-7. Mode C 40
- Table 1-8. Mode D 41
- Table 1-9. Mode E 41
- Table 1-10. Mode F 41
- Ethernet Throughput 42
- End-to-End Alarm Generation 43
- Management 44
- 1.4 Technical Specifications 45
- Environment 49
- Chapter 2 51
- Installation and Setup 51
- 2.3 Package Contents 52
- ~100 -24 0VAC 3A T 125V 53
- ~100-240VAC 3A T 125V 53
- Installing SFP Transceivers 55
- To connect to an NMS: 57
- Connecting AC Power 58
- Connecting DC Power 59
- Chapter 3 61
- Operation 61
- IPmux-16 63
- 3.3 Default Settings 64
- To enter as a superuser: 67
- To enter as a user: 67
- Overview of Menu Operations 68
- Configuration 69
- Physical Layer Configuration 69
- Timeslot Configuration 70
- IP Support 70
- To power off IPmux-8: 71
- To power off IPmux-16: 71
- Chapter 4 73
- Defining Network Managers 76
- Configuring Default Gateway 78
- Controlling Telnet Access 79
- Controlling SNMP Access 79
- Configuring Ethernet Bridge 84
- Defining VLANs 85
- Configuring E1 Interface 86
- Configuring T1 Interface 88
- 0–F (ESF) 90
- 0–3 (D4) 90
- 3, 4 for the slot 95
- 1–4 or 1–8 for the link 95
- Connecting Bundles 96
- 496 (E1), 384 (T1) 96
- Configuring IP ToS Support 103
- 4.3 Additional Tasks 105
- Setting Date and Time 106
- Managing File System 107
- Type Y to confirm 108
- Transferring Files via TFTP 109
- Resetting IPmux-8/16 110
- Chapter 5 113
- Configuring for a Typical 113
- Application 113
- Configuration Summary Table 114
- 5.3 Configuring IPmux-16 116
- Configuring Bundles 117
- IPmux-8/16 Ver. 6.00 118
- Chapter 6 121
- Troubleshooting and 121
- Diagnostics 121
- Fragments 124
- Displaying E1/T1 Statistics 125
- Displaying E3/T3 Statistics 129
- Displaying Events 141
- Clearing Events 142
- Masking Alarm Traps 143
- Working with Alarm Relay 145
- 6.3 Testing the Units 146
- Remote IPmux-16 147
- IP/Ethernet 147
- Running Ping Test 148
- Tracing the Route 149
- 6.4 Troubleshooting 150
- 6.6 Technical Support 153
- Appendix A 155
- Interface Connector 155
- Specifications 155
- A.3 CONTROL Connector 156
- Cross Cable Wiring 157
- A.4 Alarm Connector 158
- A.5 External Clock Connector 158
- Appendix B 159
- Boot Sequence for 159
- Downloading Software 159
- Boot Sequence 160
- Accessing the Boot Menu 160
- Appendix C 161
- SNMP Management 161
- MIB Structure 162
- SNMP Communities 163
- Authentication 164
- Network Management Stations 164
- Customer Response Form 169
- Error Report 171
Relacionado con productos y manuales para Gateways / Controladores RAD Data comm IPmux-8
(192 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.025 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales